Parker-hannifin Dynaserv G2 Manual de usuario Pagina 168
- Pagina / 189
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
227 Over-speed error processing type While in machine setting mode
Minimum value: 0
Maximum value: 5
Initial value: 1
Unit: None
Long:
Short:
OverSpeedErrorType
OVS_ErrTyp
Specify the processing type when an over-speed error occurs.
When operating the built-in controller axis:
0: Maintains the servo status after the axis operation stops (low level).
1: Turns the servo OFF after the axis operation stops (low level).
2: Stops the axis operation (low level) and turns the servo OFF immediately.
3: Maintains the servo status after the axis operation stops (high level).
4: Turns the servo OFF after the axis operation stops (high level).
5: Stops the axis operation (high level) and turns the servo OFF immediately.
When performing the higher controller follow-up:
0: Switches to the built-in controller, and maintains the servo status after a deceleration stop.
1: Switches to the built-in controller, and turns the servo OFF after a deceleration stop.
2: Switches to the built-in controller, performs a deceleration stop, and turns the servo OFF immediately.
3: Switches to the built-in controller, and maintains the servo status after an immediate stop.
4: Switches to the built-in controller, and turns the servo OFF after an immediate stop.
5: Switches to the built-in controller, performs an immediate stop, and turns the servo OFF immediately.
228 Over-load error processing type While in machine setting mode
Minimum value: 0
Maximum value: 5
Initial value: 1
Unit: None
Long:
Short:
OverloadErrorType
OVL_ErrTyp
Specify the processing type when an over-load error occurs.
When operating the built-in controller axis:
0: Maintains the servo status after the axis operation stops (low level).
1: Turns the servo OFF after the axis operation stops (low level).
2: Stops the axis operation (low level) and turns the servo OFF immediately.
3: Maintains the servo status after the axis operation stops (high level).
4: Turns the servo OFF after the axis operation stops (high level).
5: Stops the axis operation (high level) and turns the servo OFF immediately.
When performing the higher controller follow-up:
0: Switches to the built-in controller, and maintains the servo status after a deceleration stop.
1: Switches to the built-in controller, and turns the servo OFF after a deceleration stop.
2: Switches to the built-in controller, performs a deceleration stop, and turns the servo OFF immediately.
3: Switches to the built-in controller, and maintains the servo status after an immediate stop.
4: Switches to the built-in controller, and turns the servo OFF after an immediate stop.
5: Switches to the built-in controller, performs an immediate stop, and turns the servo OFF immediately.
- Dynaserv G2 Drive 1
- Introduction 2
- Warnings 3
- Precautions 4
- Handling Precautions 5
- The core deviation should 7
- Table of Contents 8
- Chapter 1 12
- Overview of the Product 12
- Overveiw of the Product 13
- 1.4 Model Names and Codes 16
- Chapter 2 22
- Installation 22
- Chapter 3 25
- Connection and Wiring 25
- 3.2 Cable Specification List 27
- (3) DR Series motors 29
- Terminal for <CN4> 33
- Made by Honda Tsushin Kogyo 33
- Connector: PCR-S36FS 33
- Housing: PCR-LS36LA 33
- (For 500W Level Drive Only) 35
- 4.1 Procedure (Flowchart) 37
- 4.2 Preoperation check 38
- I/O 24V Specification 39
- 2AD1820A or 40
- 4.3.1 Procedure 41
- 4.3.2 Startup 43
- 4.4 Preparation 44
- -> [String sent] 45
- <- [String received] 45
- 4.4.4 Main Menu 46
- Click OK 48
- 4.6 Auto-tuning 49
- 4.8.2 Example of Operation 54
- Chapter 5 55
- Functions 55
- 5.2 Operation Functions 57
- 5.2.4 Homing Move 59
- [Related parameters] 63
- 5.4.1 Velocity Control Part 65
- 5.5.2 Velocity Profile 69
- 5.6 Other Functions 71
- Chapter 6 75
- Control Interfaces 75
- 6.1.4 I/O logic setting 79
- 6.4 Operations 81
- 6.5 Other Inputs 83
- Chapter 7 85
- RS232C Interfaces 85
- Driver status 91
- Chapter 8 93
- 8.2 Installation 95
- 8.2.2 Starting the PC Utility 97
- DrvGII PC Utility 100
- Input text field 101
- Display text area 101
- Slider bar 107
- Frequency setting 107
- 8.5 Action Menu 111
- 8.5.3 Test Operation 115
- 8.6.2 I/O Set 119
- Chapter 9 123
- Operation Display Pendant 123
- 9.3 Switching Displays 125
- 9.5 Parameter Monitor Display 127
- 9.7 I/O Monitor Display 129
- Chapter 10 131
- Maintenance and Inspection 131
- Contents 133
- Chapter 11 136
- Specifications 136
- (1) DM Series Motor 144
- 1) Type A 144
- 2) Type B 144
- 3) DM1004B/C 144
- #365 Present velocity value 148
- Parameter List 150
- Parameter details 153
- O-Offset 155
- amount in homing mode 155
- Monitor List 170
- Monitor detail 172
- Error/Alarm List 179
- Error/Alarm Details 180
Relacionado con productos y manuales para Hardware Parker-hannifin Dynaserv G2
Hardware Parker-hannifin R-22 Manual de usuario
(4 paginas)
(4 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales